No products in the cart.
TB6600 Stepper Motor Driver Module
- Output Current: 0.5-4.0A
- Control Signal: 3.3~24V
- Power (MAX): 160W
- Micro Step: 1, 2/A, 2/B, 4, 8, 16, 32
- Temperature: -10～45℃
- Humidity: No Condensation
₹392.00₹571.12Incl. of GSTTB6600 Stepper Motor Driver Module
₹392.00₹571.12Incl. of GSTACS712 30A Range Current Sensor Module
- Supply Voltage: 4.5V~5.5V DC
- Measure Current Range: 30A
- Sensitivity: 100mV/A
- 80 kHz bandwidth
- 5 µs output rise time in response to step input current
₹79.00₹119.18Incl. of GSTACS712 30A Range Current Sensor Module
₹79.00₹119.18Incl. of GST1S to 8S Battery Level Indicator Module – Li-ion Battery Level Indicator
- Battery Supported: Lithium Battery
- Operating Temperature: -20℃~+50℃
- Working Voltage: 3V~34V (1S to 8S)
- Working Current: 5mA
- Color: Green and Outline red
₹77.00₹105.02Incl. of GST1S to 8S Battery Level Indicator Module – Li-ion Battery Level Indicator
₹77.00₹105.02Incl. of GST12V MPPT Solar Charge Controller for 3S Lithium ion Battery
- Input voltage: nominally about 18V solar panel (no-load 21V solar panel)
- Output Voltage: Nominal 12V (10.8 11.1V) Fully Charged Voltage 12.6V Lithium Battery 3 string lithium battery charge management
- Output current: maximum constant current 3A (charge current greater than 2A please add heat)
- Wiring method: pad
₹389.00₹566.40Incl. of GST12V MPPT Solar Charge Controller for 3S Lithium ion Battery
₹389.00₹566.40Incl. of GST
MQ2 Smoke and Gas Detector module
- Operating Voltage is +5V
- Can be used to Measure or detect LPG, Alcohol, Propane, Hydrogen, CO and smoke.
- Analog output voltage: 0V to 5V
- Digital Output Voltage: 0V or 5V (TTL Logic)
- Preheat duration 20 seconds
- Can be used as a Digital or analog sensor
- The Sensitivity of Digital pin can be varied using the potentiometer
₹82.00 Incl. of GSTMQ2 Smoke and Gas Detector module
₹82.00 Incl. of GSTMQ9 Gas Sensor Module – Carbon Monoxide, Methane and LPG Sensor Module
- Input voltage: DC 5V
- Power: 150mA
- DO output: TTL digital 0 and 1 (0.1 and 5V)
- AO output: 0.1-0.3V (relatively clean), the highest concentration voltage is about 4V.
₹128.60 Incl. of GSTMQ9 Gas Sensor Module – Carbon Monoxide, Methane and LPG Sensor Module
₹128.60 Incl. of GSTJT308 USB RFID Card Reader 125KHz
- Power input: USB (from a PC)
- Interface: USB, 106bit / s, no additional driver required.
- Reading distances up to 7 cm
- Frequency: 125 KHz
₹395.00 Incl. of GSTJT308 USB RFID Card Reader 125KHz
₹395.00 Incl. of GST0.36 inch 3 Digit Voltmeter – 3 to 30V DC – 2 Wire – Red Color
- 3 Digit Voltmeter
- Wire : 2
- Measuring Range: 3 to 30 VDC
- RED Colour Display
- Accuracy : 0.1 V
₹65.90₹106.00Incl. of GST0.36 inch 3 Digit Voltmeter – 3 to 30V DC – 2 Wire – Red Color
₹65.90₹106.00Incl. of GSTI2C Serial To Parallel Converter Module
- 5V power supply.
- Serial I2C control of LCD display using PCF8574.
- Backlight can be enabled or disabled via a jumper on the board.
- Contrast control via a potentiometer.
- Can have 8 modules on a single I2C bus (change address via solder jumpers)address, allowing.
₹39.00₹90.00Incl. of GSTI2C Serial To Parallel Converter Module
₹39.00₹90.00Incl. of GSTRFID Card 13.56 Mhz – MIFARE S50 Compatible
- Contactless transmission of data and supply energy (no battery needed)
- Operating distance: Up to 50mm (depending on antenna geometry)
- Operating frequency: 13.56MHz
- Data transfer: 848 kbit/s
- Anti-collision
₹15.00 Incl. of GSTRFID Card 13.56 Mhz – MIFARE S50 Compatible
₹15.00 Incl. of GSTE18-D80NK IR Proximity Sensor
- Input Voltage: 5V
- Current Consumption: 25-100 mA
- Response time <2ms
- Sensor type: Diffuse reflective type
- Sensing range: 3-80 cm
₹145.00 Incl. of GSTE18-D80NK IR Proximity Sensor
₹145.00 Incl. of GSTRaspberry Pi Pico RP2040
- RP2040 microcontroller with 2MByte Flash
- 30 multi-function General Purpose IO (4 can be used for ADC)
- Supply Voltage: 1.8V to 5V
- Micro-USB B port for power and data
- 12-bit 500ksps Analogue to Digital Converter (ADC)
₹320.00 Incl. of GSTRaspberry Pi Pico RP2040
₹320.00 Incl. of GST