No products in the cart.
VL53L1X LASER Ranging Module – Time of Flight Distance Sensor
- Emitter: 940 nm invisible laser (Class1)
- Up to 400 cm distance measurement
- Up to 50 Hz ranging frequency
- Typical full field-of-view (FoV): 27 °
- Fast and accurate long distance ranging
- Operating voltage: 2.8 – 3.3V
₹604.00 Incl. of GSTVL53L1X LASER Ranging Module – Time of Flight Distance Sensor
₹604.00 Incl. of GST12V 2 Channel WiFi Relay module
- Relay Channel: 2
- Input/Trigger Voltage (VDC): 12V DC
- Switching Voltage (VAC):250@10A
- Switching Voltage (VDC):30@10A
- Wireless relay module allows to control anything using mobile app
- Has Wifi And Hotstop Mode
- LEDs to indicate different modes and status of module
- Reserved UART debug interface and MCU download port for programming
- Only works when Mobile and Module connected to same wifi network
₹599.00₹660.00Incl. of GST12V 2 Channel WiFi Relay module
₹599.00₹660.00Incl. of GSTArduino Uno R3 Compatible Board With Cable – DIP Version
- Arduino Uno DIP Version Compatible Module
- 32 KB Flash
- 2 KB SRAM
- 1 KB EEPROM
- Frequency: 16 Mhz
₹590.00 Incl. of GSTArduino Uno R3 Compatible Board With Cable – DIP Version
₹590.00 Incl. of GSTSim800L GSM GPRS Module – 2G
- SIM800L Quad Band GSM / GPRS Module
- Power Supply: 3.7 to 4.2V Rated At 2A
- Low Power Consumption: < 3 mA during sleep mode
- Max Current: 2A (During transmission bursts)
- Supports transmission of Voice, SMS, and Data (max speed 85.6 Kbps)
- Supports Serial Communication (5v tolerant)
- Suppors Micro SIM Card
₹540.99 Incl. of GSTSim800L GSM GPRS Module – 2G
₹540.99 Incl. of GSTESP32 Programmer Board
- Supports ESP32 and ESP8266
- Can support any MCU that needs BOOT & RESET control
- USB-C Type Interface
- LEDs for Power, RX, TX
- Switch for Reset and Boot
- Both 3.3V and 5V available on the O/P connector
₹519.00 Incl. of GSTESP32 Programmer Board
₹519.00 Incl. of GSTESP32 DevKitC With UFL Connector
- Wifi Protocols: 802.11 b/g/n
- Wi-Fi +BT +BLE MCU Module
- On Chip Hall Sensor
- Integrated Crystal of 40 Mhz
- Integrated SPI Flash of 4 MB
- Recommended Voltage: 5V
₹481.00₹509.29Incl. of GSTESP32 DevKitC With UFL Connector
₹481.00₹509.29Incl. of GSTTB6600 Stepper Motor Driver Module
- Output Current: 0.5-4.0A
- Control Signal: 3.3~24V
- Power (MAX): 160W
- Micro Step: 1, 2/A, 2/B, 4, 8, 16, 32
- Temperature: -10~45℃
- Humidity: No Condensation
₹480.00₹571.12Incl. of GSTTB6600 Stepper Motor Driver Module
₹480.00₹571.12Incl. of GSTESP32 CAM Development Board – With OV2640 2 MP Camera
- Ultra-small 802.11b/g/n Wi-Fi + BT/BLE SoC module
- Low-power dual-core 32-bit CPU for application processors
- Supports interfaces such as UART/SPI/I2C/PWM/ADC/DAC
- Support OV2640 and OV7670 cameras with built-in flash
- Support TF card
₹473.70 Incl. of GSTESP32 CAM Development Board – With OV2640 2 MP Camera
₹473.70 Incl. of GST3 Phase CT Coil Module – 100A
- 3 Phase CT Coil Module
- Analog Output
- Current to Voltage Ratio: 10:1 (1V for 10 A)
- Max Current Detection: 100 A
- Min Current Detection: 6 A
₹472.00 Incl. of GST3 Phase CT Coil Module – 100A
₹472.00 Incl. of GST300W Step Down DC-DC Buck Converter with Constant Voltage and Current Control – CC – CV – 20A
- Output Voltage: 1.2V to 36V DC
- Input Voltage: 6V to 40V DC
- Output Current: 20A(max.)
- Efficiency: 95%(24V to 12V, 20A)
- Output Ripple: ≤50mV
- Wiring Method: Terminal
- Short Circuit Protection: Self-recovery(cannot short circuit for long time)
₹440.00 Incl. of GST